Home
Conveyor Component
Sampling System
Magnetic Separator
Stacker & Reclaimer
Weigh Feeder

 

 

ARCH - USA

Safety Devices - Belt Cleaners Primary & Secondary 

Belts Scales - Metal Detectors - Accessories & Etc.

 
 

PULL CORD SWITCHES

CTS 100 Standard Rotary Switch

The CTS 100 uses an electrical rotary switch, allowing personal to trip it manualy. The electrical switch is a self-wiping rotary switch (not a micro-switch), and consists of two normally open and two normally closed contacts. One the switch has been tripped, the orange colored flag is in the "Up" position to alert maintenance personnel.  It must then be manualy reset in order to restart the conveyor.

Non-Hazardous Environments Only, Self-Wiping Rotary Switch, Lockable Switch

 

 

 

   
   

CTS 200L Standard W/Trip Light

The CTS200L uses an electrical rotary switch, allowing personal to trip it manualy. The electrical switch is a self-wiping rotary switch (not a micro-switch), and consists of two normally open and two normally closed contacts. One the switch has been tripped, the orange colored flag is in the "Up" position to alert maintenance personnel.  It must then be manualy reset in order to restart the conveyor.

Non-Hazardous Environments Only, Self-Wiping Rotary Switch, Trip Indication, Lockable Switch

   
   
CTS 300PSW Switch W/Pre-Start Alarm

The CTS 300 PSW is a self-wiping rotary switch (not a micro-switch) and consists of two normally open and two normally closed contacts. One the switch has been tripped, The Blue colored flag is in the "Up" position. The CTS 300 PSW also emits an "Audible" alarm sounfd before "Start Up" of the conveyor to warn maintenance personnel that the conveyor is about restart.

(This Switch should only be used in conjuction with an ARCH "CMS - Conveyor Monitoring System" and not as a stand-alone switch. Once tripped it must be manually reset to restart the conveyor)

Hazardous / Non-Hazardous environments, Audio/Visual Pre-Start Alarm, Trip Indication LEDs, Lockable Switch

 

   
   
CTS 900 AVA Audio/Visual Pre-Start Alarm

The CTS 900 AVA alarm unit is housed in a high impact UV Stabilized polycarbonate enclosure rated to IP 65 degrees of protection. The unit consists of : 1 alarm buzzer rated 105 dB and flasing strobe light.

Audio and Visual Alarm, Haevy Duty Housing, Corrosion Proof 

   
   

CMS 3000-HECU Head End Control Unit

The CTS 3000 is an intelligent, programmable control unit with internal fault diagnostics.  The Head End Control Unit (HECU) controls, monitors, and supervises all safety and belt protection devices. Each fault condition is identified and displayed by name/type on the Touch Screen.  The HECU provides maintenance personnel with the information necessary to locate problems quickly, minimizing conveyor downtime.

 

   
   

CTS 700 BL Belt Misalignment Detector

 

Arch’s CTS 700 BL utilizes a mechanical delay to prevent trips from incidental misalignment.  The switch features two upright arms connected to a rotary switch that will shut down a conveyor before damage is done.

(Once activated, the switch must be manually reset)

For Belts 24” to 96”, Bolt-in-Place Installation, Detects Misalignment in Both Directions

   
   

CTS 700 RBL Return Belt Misalignment Detector

The CTS 700 RBL uses two downcast arms to detect misalignment of a return belt.  Should the belt run off to the right or to the left to the extent that it can cause damage to the belt or the conveyor structure, it will come into contact with one of the downcast arms.  These arms are connected to an electrical switch via a glass-reinforced polycarbonate made coupling mechanism.

 

For Belts 24” to 96”, Bolt-in-Place Installation, Heavy Duty Housing

 

   
   

CTS 700 BTR Rip & Tear Detector

The CTS 700 BTR’s two profiled arms connect to a rotary switch equipped with a mechanical delay to prevent trips from incidental contact.

(Once activated, the switch must be manually reset)

For Belts 24” to 96”, Detects Side Wing Tears and Center Rips, High-Impact Housing

   
   

CTS 9000 Infrared Rip Detector

 

The CTS 9000 IRD is equipped with a push-button that starts a wash cycle without stopping the conveyor. The wash cycle will allow the operator five minutes to clear the lens and the unit will return online automatically. The total unit consists of 3 IP 66 enclosures mounted on a metal bracket facing each other with the sensing beams, an electronic control unit which is mounted on the bracket facing out, and a special metal tray to catch the falling material.

Auto-Wash Mechanism, For Belts 24” to 96”, Minimum Recalibration, High-Impact Housing

 

   
   

Tri-Return Training Idler

 

The Tri-Return Training Idler uses a patented convex arrangement of three self-adjusting idler rolls on a center pivot that automatically centers your conveyor belt. The center roll is horizontal and the two outer rolls are mounted at a descending angle. This roll arrangement allows the trainer to fit the full cup of the return conveyor belt.

Rubber Coated Rolls, Steel Construction, Bolt-in-Place installation, Easily Replaces Current Idlers

 

   
   

CTS 600 BCD Blocked Chute Detector

 

The CTS 600 BCD blocked chute detector is a tilt-type switch, which is mounted inside the chute to monitor any blockage in the material conveyed. Should material start to build up due to a blockage, it will lift the sensing rod, tilting the switch; any tilt to the switch above 15 degrees will cause one of the steel-encapsulated switches to open.  This unit provides a relay interface between a tilt-type probe and the conveyor control system.

Polyurethane Construction, Encapsulated Probe, Adjustable Timer, Corrosion Resistant

   
   

CTS 700 OSU Belt Off Speed Monitor

 

The CTS 700 OSU uses a roller mounted underneath the troughing belt to detect belt movement. A pulse sensor is mounted on the roller structure and monitors the pulses in magnetic proximity mode.

Easy Setup, Zero Speed Monitor Also Available

 

 

 

   
   

EMT 50 Metal Detector

 

The EMT 50 has a 5 percent sensitivity level and can be tuned to ignore conductive or magnetic ores, such as magnetite or pyrite (even if they’re carried by high-tension steel cord belts with rip detection loops). The EMT 50 will still detect small pieces of tramp metal. Its lightweight construction allows for easy assembly and installation, even as a flat-pack, under-belt style.

(Available for nearly any belt width)

   

   

   
   
   

EMT 100 Metal Detector

 

Equipped with a 10 percent sensitivity level, the EMT 100 can detect both ferrous and non-ferrous metals. It can be used on belts containing metallic repair clips or splices with our optional clip detector. The aperture can be adjusted up to 23.5” to accommodate burden heights up to 19.5.” The lightweight, flexible design also allows the detector aperture to be moved in the field.

(Available for belt widths up to 48)

 
   
   

Saber® Channel Mount (SCM) Primary Cleaner

 

An upgraded version of our Saber® Primary cleaner, the SCM features a reinforced frame and a channel-mount design for faster blade replacement from either side of the conveyor.

18″ to 120″ Conveyor Belts, Safe for Mechanical Splices, Non-Segmented Blade, Channel-Mount Frame

 

   
   

Saber® (SB) Primary Cleaner

 

The Saber® Primary cleaner features a 100% premium polyurethane blade and steel frame that allows it to take even more abuse than ever before.

 

18″ to 120″ Conveyor Belts, Safe for Mechanical Splices, Non-Segmented Blade

 
 
 
   
   

Saber® Max Primary Cleaner

 

Available with single or dual Twister® Tensioners and steel mainframe, the Saber® Max is no slouch when it comes to hard work.  This robust cleaner utilizes the same proven Saber® blade profile in a bigger, stronger package.

18″ to 120″ Conveyor Belts, Safe for Mechanical Splices, Non-Segmented Blade, Heavy Duty Applications

 

 
   
   

Super Saber® Primary Cleaner

 

With a HUGE segmented blade pressed on a heavy-duty steel frame and dual Twister® Tensioners, the Super Saber® is the premier defense against stubborn carryback on large belts. Recommended for 30” head pulleys or larger, this is the big solution for big belts.

 

8″ to 120″ Conveyor Belts, Safe for Mechanical Splices ,Segmented Blade, Heavy Duty Applications

 

 
   
   

Saber® Dual Primary Cleaner

 

Two Saber® Channel Mount primary cleaners mounted at the head pulley for extra defense against carry back. Dual primaries are also available in the Arch Mini and Saber® Max cleaners.

 

 
   

 

 

Mini Saber® Primary Cleaner

 

Featuring big performance from a little blade, the Mini Saber® is ideal for head pulleys 18″ or smaller.

 

18″ to 48″ Conveyor Belts, Safe for Mechanical Splices, Non-Segmented Blade, 18″ Head Pulleys or Smaller

 

 
   
   

Saber® GSS Secondary Cleaner

 

Arch Saber® Secondary (GSS) cleaners, like Saber® Primary cleaners, use a super-premium polyurethane blade that handles carryback along the return side of the belt. Its cantilever design maintains optimum cleaning pressure while letting mechanical splices pass harmlessly, saving the blade, belt, and splice from damage.

18″ to 72″ Conveyor Belts, Safe for Mechanical Splices, Non-Segmented Blade

 
   
 
 

RBS Secondary Cleaner

 

Using metal-blade technology, the RBS Secondary cleaner eliminates stubborn tack and slime sometimes missed by primary cleaners with a precision-crafted tungsten carbide blade. Delivered pre-assembled to your specifications, this aggressive secondary cleaner is easy to install and handles the toughest conditions at any belt speed.

 

18″ to 120″ Conveyor Belts, Tungsten Carbide Blade, Fixed Lugs Available

 

 
   

 

 

RGS Secondary Cleaner

 

Utilizing the same cantilever design as the GSS cleaner, the RGS Secondary cleaner takes it a step further. A tungsten carbide blade encased in urethane makes easy work of any residual material missed by a primary cleaner.

18″ to 72″ Conveyor Belts, Tungsten Carbide Blade, Splice Tolerant, Heavy Duty Applications

 

 
   
   

Saber® Roller

 

The Arch Saber Roller puts a new spin on the conventional “beater roll” used in the industry for years.  Using the proven Saber blade profile, this secondary cleaner will scrape the belt clean while providing the same vibratory action needed to remove excess material from the belt.

 

Perfect for belts that are cleated, textured, reversible, and/or in general poor condition.

   
   

V-Plow Angle Plow

 

V-Plow discharges material off both sides of the belt while the Angle Plow removes it to one side only. These solutions eliminate uneven buildup on the tail pulley that leads to belt misalignment.

Standard blades for V-Plow are black rubber and red urethane for Angle Plow

 

 
   
   

Archweigh SC Belt Scale

 

The Archweigh Dual SC offers a weight accuracy of 1 1% – 2% as it self-adjusts to the movement of the belt, thanks to Arch’s patented dual-ended load cells.  This unique engineering compensates for outside forces on the belt by forcing converse reactions by the load cells; one is forced up while the other pushes down.  (Constant recalibration is never necessary)

No assembly required, Bolt-in-Place Installation, Minimum Recalibration

 

 
   
   

Archweigh HP Belt Scale

 

The Archweigh HP is the only belt scale that accounts for outside forces that affect every conveyor.  Arch’s patented dual-ended load cells mount directly to the idler, and provide reliable, accurate data (up to +/- 1/2%) every day without recalibration. The dual load cells work opposite each other to neutralize the natural lateral and vertical movements of your conveyor belt.  As a force pushes down one end, that same force naturally lifts the other; any movement is cancelled out.

 

No assembly required, Bolt-in-Place Installation, Minimum Recalibration

 
   
   
Archweigh Scale Integrators

 

Manages Up To 6 Scales-Touchscreen Display-Unlimited Communication Options.

The Archweigh belt scales are uniquely designed mechanically and electrically. Arch’s patented load cell design eliminates problems associated with weighing material on a moving conveyor belt. With other scales, the force created by the movement of the belt over the scale carriage is factored as a component of the calibration weight or Belt-Tare. The assumption that mechanical components will not vary over time results in a lack of long term accuracy and repeatability. Therefore, the output value of the load cell is always only the weight of the material on the belt, nothing more and nothing less. With our scales, there are no parts to bolt together or kits to figure out. Let us prove to you that we provide better service, installation, and belt scales. Arch installation services are available to any of our customers or we’ll train your staff to properly install, set up, calibrate and maintain your equipment.

 

   
   

Archweigh 1000 Scale Integrator

 

The Archweigh Integrator utilizes a unique Analog-to-Digital conversion process which allows for the use of an industry standard programmable logic controller (PLC) as a control processor. The exclusive converter internally performs thousands of weight and speed calculations per minute and transmits that high accuracy value to the PLC. The processor then uses those numbers to perform basic rate, weight, and totalizer calculations.

 

Single-Scale Integrator-Touchscreen Display-Unlimited Communication Options

   
   

Archweigh 2000 Scale Integrator

 

Built with the same rock-solid, time-tested software and analog-to-digital conversion as the Archweigh 1000, the Archweigh 2000 is built for multiple scales carriages. A 6″ touch screen display makes set-up and calibration easy to do anywhere. A steel enclosure makes the ArchWeigh 2000 as tough as the environment it works in.

 

   
   

Simplicity Impact System

 

Constructed with more steel than most impact beds, Simplicity Impact Systems provide 75 percent more belt support than conventional impact beds.  The impact bars rely on the strength and durability of steel to handle heavy, bulky material, just like the frame.  The steel sub-frames in the bars are molded into a shock absorbing rubber and capped with low-friction UHMW, giving your belts a smooth ride out of the loading zone.

100% Customizable, Steel Construction, Bolt-in-Place installation, Supports Length and Width of load zone

 
   
   

Simplicity Slider System

 

Load zones create problem areas, especially those that are unsupported.  Arch’s Simplicity Slider System fills in problematic gaps in the load zone.  Slider Bar inserts allow the use of existing idler stands or can be replaced with new stands. 

100% Customizable, Steel Construction, Bolt-in-Place installation Supports Length and Width of load zone

 
   
   

Simplicity Impact SD Bars

 

Simplicity (SD) Impact Bars are a cost effective alternative to our Heavy Duty (HD) Steel Impact Bars.  The SD Impact Bars not only work in Arch Simplicity Impact Systems, but are also a direct replacement for other manufacturers bars.  The aluminum sub-frames in the bars are molded into a shock absorbing rubber and capped with low-friction UHMW, giving your belts a smooth ride out of the loading zone.

Aluminum  Construction, Bolt-in-Place installation, Supports Length and Width of load zone

   
   

Cam-A-Lot

 

Utilizing a cam action, the Cam-A-Lot Clamp System makes quick work of changing skirtboard rubber.  360 degree rotating clamp heads allow for a custom fit in an otherwise unusable space.  Simple and easy weld on installation makes the Cam-A-Lot a hassle free solution to load zone sealing.

 

Manufactured in 5 foot sections, Will work with most existing seals (recommended to be paired with Arch Talon Seal).

   
   

At-Last-A-Seal® Sealing System

 

At-Last-A-Seal® skirt seal takes a new approach to sealing transfer points; they become a part of the chute wall and float on the belt, allowing the conveyed material to apply sealing pressure without excessive drag and friction. This solution encapsulates the bottom edge of the chute wall and harmlessly rides on the surface of the belt. This lets the seal ‘float’ and conform to any irregularities and inconsistencies of the belt surface.

Up to 500 ft., ’Floating Seal’, No Splices or Joints, Super Duty Applications

 
   
   

Talon Sealing System

 

The Talon Seal uses a unique design with multiple barriers to contain dust and fines to the belt. This seal leverages the weight of the load to either increase or decrease the seal-to-belt pressure; heavy loads create more pressure, lighter loads less pressure.

 

Use With Existing Clamps, Continuous Lengths up to 200’, Minimal Friction

 
   
   

Flexiskirt Sealing System

 

Flexiskirt sealing systems utilize directionally grooved rubber to force fines back into the bulk flow. Recommended for very dry, dusty materials, this design takes advantage of the rubber’s natural flexibility to seal the belt by conforming to the belt surface. Able to withstand temperatures of up to 150°F, Flexiskirt seal conforms to the belt’s dynamics with minimal friction as it adapts to widening or narrowing gaps between the belt and seal chute wall.

18″ to 120″ Conveyor Belts, Safe for Mechanical Splices

 
   
   

Simplicity Chute Baffles

Featuring double-layer wear-resistant polyurethane, Simplicity Chute Baffles trap and contain dust particles. The overlapping design provides double the protection against harmful fugitive dust. 

Stop Escaping Dust, Customizable to Your Dimensions.

 

 
 
   
   

Agglomerative Dust Control

 

The cluster spray heads are equipped with the standard #3 nozzle. The number of nozzles depends upon the spray head required. A filter and ball valve may be added to the spray bar or head.  Pumps are equipped with one filter, one ball valve, a pressure regulation valve, and pressure gauge.  Motors are available in 120/240 or 230/460 voltage.

Low Water Consumption, No Chemical or Air Injectors

 

 
   
   

 

Home | Conveyor Component | Sampling System | Magnetic Separator | Stacker & Reclaimer | Weigh Feeder


Copyright © PT. MAT